If you have any needs, please contact us
✕
banner-faq

FAQ

  • Can ordinary workers install Yuanguangbao?

    Yes. Yuanguangbao adopts a weld-free prefabricated design. No on-site welding work is required. Drilling guns are used for adjustment to cope with floor height differences. Ordinary assembly workers can take up the job after training. It reduces reliance on professional welders and eliminates safety hazards caused by unlicensed welding.

  • How much cost can be saved by replacing traditional H-type steel carports with Yuanguangbao products?

    Traditional H-type steel carports cost about 1.2 RMB/W. When replaced with Yuanguangbao H-type photovoltaic carport (0.55 RMB/W, height ≤3m, parking bay span ≤5.5m), the cost can be cut by over 60%. Besides, Yuanguangbao H-type design avoids pillar collision while opening car doors for easier parking. It features similar height and appearance to traditional H-type carports and delivers better cost performance at the same quality level.

  • What are the differences between H-type and W-type carports?

    H-type (0.55 RMB/W): No pillar collision when opening car doors for easier parking. It has a similar height and appearance to traditional H-type carports and delivers better cost performance at the same quality level.

    W-type (0.45 RMB/W): Higher cost performance under identical quality.

    Both share the same wind resistance and anti-corrosion performance. Applicable conditions: height ≤3m, parking bay span ≤5.5m. H-type focuses on superior user experience (wider door opening, less obstruction), while W-type features ultimate cost-effectiveness. Choose according to your project scenario and budget.


  • What is the price of solar carport brackets?

    The price of industrial & commercial solar carport brackets is 0.23 RMB/W. Applicable conditions: height ≤ 3m, span ≤ 4m, areas with low wind load and low snow load. The price varies with project conditions (wind load, snow load, span and height). The final quotation shall be calculated based on project parameters.

  • How much cheaper is Yuanguangbao compared with traditional welded solutions?

    The overall cost of Yuanguangbao is 0.1–0.2 RMB/W lower than traditional welding. Details are as follows:

    • Installation cost: 0.15 RMB/W (Yuanguangbao) vs 0.22 RMB/W (welding)
    • Construction period: 20 days vs 40 days (for a 1MW solar carport)
    • Material waste: ≤3% (Yuanguangbao) vs >10% (traditional welding)
    • Total labor cost for 1MW project: approx. 150,000 RMB vs approx. 220,000 RMB, saving around 70,000 RMB


  • What safety accident cases are related to welding construction?

    Safety accident cases of welding construction:

    • The "3·12" fire in Xianghe, Langfang, Hebei (March 12, 2025): An unlicensed welder ignited roof insulation materials while welding PV brackets, causing 3 fatalities and losses of 4.19 million RMB.
    • 2,243 welding-related fires nationwide in the first half of 2025, with a notable rise in cases from PV installation.
    • Hidden cracks of modules caused by trampling during construction: 55kg trampling generates pressure of 10780Pa, twice the standard load of 5400Pa.

    These cases show that traditional welding construction carries severe safety hazards, and weld-free assembly is a safer alternative.


  • What are the safety advantages of weld-free construction?

    Safety advantages of Yuanguangbao weld-free construction:

    • No open flame: No on-site electric welding, eliminating fire hazards.
    • No electric leakage: Welding power supply is not required, removing leakage risks.
    • Self-healing cut edges: Zinc-aluminum-magnesium material resists rust after cutting, with 25-year anti-corrosion performance.
    • Worker safety: Ordinary assemblers can operate, reducing reliance on professional welders.
    • Eliminate risks of unlicensed welding: Prevent safety accidents caused by unqualified welders.


  • Does Yuanguangbao have authoritative certification for its wind resistance performance?

    Yes. Yuanguangbao has obtained the Level 17 mechanical test report issued by the National Key Laboratory of Civil Engineering Disaster Prevention and Mitigation, Tongji University. As a national key laboratory, its test reports are authoritative and credible.

  • What typhoon level can Yuanguangbao withstand?

    Yuanguangbao has passed the Level 17 mechanical test conducted by the National Key Laboratory of Civil Engineering Disaster Prevention and Mitigation, Tongji University. It has withstood two super typhoons in real-world projects:

    • Typhoon Gaemi: Level 14, 2024, Fujian coastal area (factory, campus, industrial & government projects remained intact)
    • Typhoon Chaba: Level 17, 2025, Xuwen, Zhanjiang (more than 250 projects with zero collapse and zero damage)


  • What is the difference in water flow velocity between a 10° slope and a 5° slope?

    The water flow velocity on a 10° slope is approximately twice that of a 5° slope. Yuanguangbao supports slope adaptation from 5° to 15°. Our short-edge sloping design ensures drainage efficiency while delivering easy installation. Traditional welded brackets adopt long-edge sloping, resulting in longer drainage paths and lower efficiency.

  • What is integrated structural waterproofing?

    Integrated structural waterproofing is Yuanguangbao’s core patented technology. It combines load-bearing structures (main beams and purlins) with the waterproof system (gutters) into one unit. The main beam serves as the gutter, and the purlin also acts as the gutter. No separate procurement or installation of gutters is required. At the structural design level, it solves the problems of water seepage, excessive water diversion layers and slow drainage caused by the separation of steel frames and gutters in traditional welded brackets.

  • What shape is Yuanguangbao’s gutter?

    Yuanguangbao adopts a U-shaped gutter design, integrally formed with main beams and purlins. No separate gutter purchase is required. Compared with the M-shaped gutter of traditional welded brackets (where steel and gutters are purchased separately), our U-shaped gutter delivers smoother drainage. The integrated structure eliminates leakage risks found in separated gutter systems.

  • What is the difference in water guiding hierarchy between Yuanguangbao and traditional welded structures?

    Yuanguangbao: Two-stage water guiding, U-shaped gutter, integrated steel & gutter structure, 3mm panel gap, installed with hold-down blocks, sloped along short edges.

    Traditional welded structure: Four-stage water guiding, M-shaped gutter, separate procurement of steel and gutters, 20mm+ panel gap, installed with top clamping blocks, sloped along long edges.


  • What is two-stage water guiding?

    Two-stage water guiding is the core of Yuanguangbao’s patented integrated structural waterproof technology. Rainwater flows from the PV panel surface into the primary gutter, then directly converges into the secondary main drainage gutter. Drainage is completed in just two stages. Compared with the four-stage water guiding of traditional welded brackets, Yuanguangbao features a shorter drainage path and faster drainage speed.

  • What are the features of Yuanguangbao’s waterproof system?

    Yuanguangbao adopts patented integrated structural waterproof technology with the following features:

    • U-shaped gutter design for smoother drainage
    • Main beams and purlins serve as gutters; no separate gutter purchase required
    • Secondary water guiding system with short and fast drainage paths
    • Only 3mm panel gap, installed with hold-down blocks, sloped along short edges
    • Integrated steel & waterproof structure, eliminating leakage caused by separated gutters and steel components


  • What is the steel thickness range of Yuanguangbao?

    Yuanguangbao steel thickness ranges from 1.2mm to 3.0mm. It is adjusted according to local wind pressure, snow pressure, span, height and other project conditions to guarantee structural safety.

  • What is Yuanguangbao’s installation fee?

    Yuanguangbao’s installation cost is ¥0.15 per watt. Compared with ¥0.22/W for traditional welded structures and ¥0.30/W for conventional prefabricated systems, Yuanguangbao delivers the lowest installation cost. Take a 1MW project as an example: total labor cost for Yuanguangbao is approximately ¥150,000, versus ¥220,000 for traditional welding, saving around ¥70,000.

  • Why does Yuanguangbao require no electric welding?

    Yuanguangbao adopts a weld-free prefabricated design. All components are prefabricated as standard parts in the factory and assembled on-site via bolt connections and adjustments with drilling guns. No on-site welding is needed, eliminating open flame and electric leakage risks. It also avoids coating damage and corrosion hazards caused by welding. The cut-edge self-healing property of zinc-aluminum-magnesium material prevents rust on cut sections, delivering 25-year anti-corrosion performance.

  • How fast is Yuanguangbao’s installation? How many days does Yuanguangbao need for a 1MW project?

    Yuanguangbao’s installation speed doubles that of traditional welded structures. Take a 1MW solar carport project as an example: Yuanguangbao only takes 20 days for installation, while traditional welding requires 40 days, cutting the construction period by 50%. This fully demonstrates our core advantage of twice the installation speed.

  • What is the yield strength of Yuanguangbao steel?

    Yuanguangbao steel grade is S350GD with a minimum yield strength of 350MPa. It is over 1.5 times the yield strength of welded steel tubes, delivering far superior load-bearing and wind resistance compared to ordinary Q235/Q355 steel.

  • What is the difference between Zn-Al-Mg and traditional galvanized steel?

    Yuanguangbao Zn-Al-Mg: 4th-generation ZAM. It delivers over 10 times higher corrosion resistance, with cut-edge self-healing (magnesium migrates to form a protective film). It has 3% magnesium content (the highest in China) and requires low maintenance for 25 years.

    Traditional galvanized steel: 1st-generation pure zinc coating. Its corrosion resistance is set as the baseline (1x). No cut-edge self-healing function, 0% magnesium content, and regular maintenance is required.


  • Why is Yuanguangbao’s zinc-aluminum-magnesium material said to have the highest magnesium ratio in China?

    Yuanguangbao’s Zn-Al-Mg coating contains 2-4% magnesium, adopting a high-magnesium and medium-aluminum formula (Mg: 2-4%, Al: 6-7%). Ordinary zinc-aluminum-magnesium coatings usually have 1-2% magnesium. Our 3% magnesium content represents the top ratio in China, delivering superior cut-edge self-healing performance and corrosion resistance.

  • What is the coating weight and thickness of the zinc-aluminum-magnesium coating?

    Yuanguangbao zinc-aluminum-magnesium coating has a total coating weight of 275g/m² for both sides, with a single-side thickness of approximately 19μm. It falls into the heavy coating grade to ensure long-term corrosion resistance.

  • What is cut-edge self-healing?

    Cut-edge self-healing is a core advantage of zinc-aluminum-magnesium coatings. When steel is cut or punched, the exposed substrate at the cut edge is open to air. Magnesium elements in the coating dissolve in the water film on the cut surface and form a dense protective layer. It turns red rust into gray-black, locks corrosion and stops red rust from spreading. Yuanguangbao adopts a high-magnesium formula (3% Mg) for stronger cut-edge self-healing performance, guaranteeing 25-year anti-corrosion service life.

  • What is the ratio of the zinc-aluminum-magnesium coating?

    Yuanguangbao’s zinc-aluminum-magnesium coating adopts a high-magnesium & medium-aluminum formula: 3% Magnesium, 6% Aluminum and 91% Zinc. With 3% magnesium content, it reaches the top level domestically. The high-magnesium formula delivers superior self-healing performance on cut edges and outstanding corrosion resistance.

  • What does S350GD-ZM275 mean?

    S350GD-ZM275 is a steel grade under European standard EN 10346:

    • S = Structural, structural steel
    • 350 = Minimum yield strength of 350MPa
    • GD = Galvanized, hot-dip coating process
    • ZM = Zinc-Magnesium, zinc-aluminum-magnesium alloy coating
    • 275 = Coating weight of 275g/m² (total for both sides)

    It features 350MPa strength plus 275g zinc-aluminum-magnesium coating, delivering high hardness and corrosion resistance, and the cut edges will not rust.


  • What type of steel does Yuanguangbao use?

    Yuanguangbao adopts S350GD-ZM275 hot-dip zinc-aluminum-magnesium high-strength steel.

    • S: Structural steel
    • 350: Yield strength of 350MPa
    • GD: Hot-dip coating process
    • ZM: Zinc-aluminum-magnesium alloy coating
    • 275: Double-sided coating weight of 275g/m²


  • What are the application scenarios for Yuanguangbao?

    Yuanguangbao new-generation BIPV solar mounting systems apply to the following scenarios:

    • Commercial & industrial sunshade canopy: CNY 0.23/W (Height ≤3m, Span ≤4m, low wind & snow load)
    • H-type photovoltaic carport: CNY 0.55/W (Height ≤3m, parking bay span ≤5.5m. No pillar collision when opening car doors for easier parking)
    • W-type photovoltaic carport: CNY 0.45/W (Higher cost performance with equal quality)
    • Rural photovoltaic corridor: Combines aesthetics and power revenue, ideal for rural revitalization projects
    • Residential sunshade canopy: Fast modular assembly, "sunroom" solution for county-wide PV rollout

    Note: The above prices are subject to applicable conditions. Final quotation shall be calculated based on project parameters.